[1]王铎、沈振辉、杨拴强.外力作用下FDM构件失效分析[J].福建工程学院学报,2021,19(01):32-36.[doi:10.3969/j.issn.1672-4348.2021.01.006]
　WANG Duo,SHEN Zhenhui,YANG Shuanqiang.Failure analysis of FDM components under external compression[J].Journal of FuJian University of Technology,2021,19(01):32-36.[doi:10.3969/j.issn.1672-4348.2021.01.006]
点击复制

外力作用下FDM构件失效分析()
分享到：

《福建工程学院学报》[ISSN:2097-3853/CN:35-1351/Z]

卷:
第19卷
期数:
2021年01期
页码:
32-36
栏目:
出版日期:
2021-02-25

文章信息/Info

Title:
Failure analysis of FDM components under external compression
作者:
王铎、沈振辉、杨拴强
福建江夏学院
Author(s):
WANG Duo;  SHEN Zhenhui;  YANG Shuanqiang
Institute of Industrial Technology, College of Engineering, Fujian Jiangxia University
关键词:
压缩实验; 构件; 失效分析
Keywords:
FDM;  compression test;  compoment;  failure analysis
分类号:
TQ323
DOI:
10.3969/j.issn.1672-4348.2021.01.006
文献标志码:
A
摘要:
为探究FDM零件压缩作用下连续变形失效的机理，对125种不同构型的零件压缩实验比较力学性能。基于正交实验设计理论，通过多因素组合分析确定零件连续变形失效原因。正交实验结果表明，抗压缩强度影响从大到小排序为层片厚度、材料种类、填充率、打印质量。采用仿真手段模拟了压缩变形后微观失效的变化规律。结果表明，材料进入塑性阶段必须考虑损伤形成的影响，塑性阶段后促进损伤扩展，应防止构件出现塑性过程导致局部失效破坏，验证了模拟方法的合理性。
Abstract:
In order to explore the mechanism of continuous deformation failure of FDM parts under compression, the mechanical properties of 125 parts with different configurations were compared. Based on the theory of orthogonal experimental design, the causes of continuous deformation failure of parts were determined by the combination analysis of various factors. Results of the orthogonal experiment show that the thickness of laminate is the most important factor affecting the compressive strength, followed by the type of material, and then the filling rate, and finally the printing quality. The change law of micro failure after compression deformation was simulated. Simulation results show that the impact of damage formation must be considered when the material enters the plastic stage, and the damage expansion can be promoted after the plastic stage. The plastic process of the component should be avoided, which would lead to local failure. The rationality of the simulation method was verified.

参考文献/References:

[1] 刘晓军, 迟百宏, 焦志伟, 等. FDM大型3D打印机的制作与工艺分析[J]. 机械设计与制造, 2018（11）: 212-215.[2] DAWOUD M, TAHA I, EBEID S. Mechanical behaviour of ABS: an experimental study using FDM and injection moulding techniques[J]. Journal of Manufacturing Processes, 2016, 21: 39-45.[3] DOMINGO-ESPIN M, PUIGORIOL-FORCADA J, GARCIA-GRANADA A, et al. Mechanical property characterization and simulation of fused deposition modeling Polycarbonate parts[J]. Materials & Design, 2015, 83: 670-677.[4] HUANG B, SINGAMNENI S. Raster angle mechanics in fused deposition modelling[J]. Journal of Composite Materials, 2015, 49（3）: 363-383.[5] LEE W, SHEN H. Comparisons of deformation and fracture behaviour of PC/ABS blend and ABS copolymer under dynamic shear loading[J]. Materials Science and Technology, 2004: 20(1): 8-15.[6] 丁源. ABAQUS 2018有限元分析从入门到精通[M]. 北京: 清华大学出版社, 2019.

更新日期/Last Update: 2021-02-25