[1]叶建华,曾寿金,许明三,等.截面相似性零件的自适应测点规划研究[J].福建工程学院学报,2018,16(04):331-335.[doi:10.3969/j.issn.1672-4348.2018.04.005]
 YE Jianhua,ZENG Shoujin,XU Mingsan,et al.Research on adaptive measure point planning for parts with similar sections[J].Journal of FuJian University of Technology,2018,16(04):331-335.[doi:10.3969/j.issn.1672-4348.2018.04.005]
点击复制

截面相似性零件的自适应测点规划研究()
分享到:

《福建工程学院学报》[ISSN:2097-3853/CN:35-1351/Z]

卷:
第16卷
期数:
2018年04期
页码:
331-335
栏目:
出版日期:
2018-08-25

文章信息/Info

Title:
Research on adaptive measure point planning for parts with similar sections
作者:
叶建华曾寿金许明三黄卫东
福建工程学院机械与汽车工程学院
Author(s):
YE Jianhua ZENG Shoujin XU Mingsan HUANG Weidong
School of Mechanical & Automotive Engineering, Fujian University of Technology
关键词:
测量规划曲面采样截面相似性零件
Keywords:
measure planningcurved surface samplingparts with similar sections
分类号:
TH161.21
DOI:
10.3969/j.issn.1672-4348.2018.04.005
文献标志码:
A
摘要:
针对整个模型统一尺度规划和曲面间的衔接处理困难问题,提出“曲面模型-三角网格模型-截面线-点集-测点集”的规划策略,实现基于曲率特性的自适应测点规划。通过将数字化设计模型转换成统一粒度的密集三角网格模型,实现复杂型面的一致性描述;进而利用三角网格的拓扑信息,提取截面线;在截面线曲率估算的基础上,通过均分曲线质量进行测量点的自适应规划。结果表明,该研究能以较少的测点反映加工误差。
Abstract:
For the problem of uniform scale planning and convergence processing among multiple surfaces, a planning strategy of “curved surface model-triangular mesh model-section line-point set-measuring point set” was proposed to implement adaptive measure point planning based on curvature characteristics. The digital design model was transformed into a uniform granular dense triangular mesh model to achieve a consistent description of the complex surface. The section line was extracted by using the topological information of the triangular mesh. Based on the estimation of the curvature of the section lines, the adaptive measure point planning was performed with an equal division of the curves’ mass. The results of the simulation show that the method can reflect the machining errors with fewer measuring points.

参考文献/References:

[1] 周阿维, 邵伟, 吴莹. 应用锥光偏振全息技术的航空叶片测量新方法[J]. 中国机械工程, 2017, 28(12): 1394-1399.
[2] 蔺小军, 单晨伟, 王增强,等. 航空发动机叶片型面三坐标测量机测量技术[J]. 计算机集成制造系统, 2012, 18(1): 125-131.
[3] 杨海成, 王玉, 单纯利. 航空发动机压气机叶片前后缘测量方法评述[J]. 航空精密制造技术, 2015, 51(6): 43-45.
[4] 陈细涛. 航空叶片原位检测方法与实验研究[D]. 武汉:华中科技大学, 2012.
[5] 陈岳坪,靳龙,卢海燕,等. 基于三角网格模型的复杂曲面测点规划[J]. 机床与液压, 2015(23): 42-45.
[6] 陈佳佳, 王彪, 陈磊,等. 基于形心模型的已知自由曲面测量点规划研究[J]. 机床与液压, 2015, 43(9): 129-131.
[7] 何改云,贾红洋. 基于CAD模型的自由曲面自适应采样策略术[J]. 电子测量与仪器学报, 2012, 26(10) :835-840.

更新日期/Last Update: 2018-08-25